BringupDocumentation
ENDE
Open the editor
Behavioural mixed-signal modelDRV8833PWPRdrv8833

DRV8833 dual H-bridge motor driver

Two MOSFET H-bridges for 2.7–10.8 V, 1.5 A RMS per bridge: on-resistance 200 mΩ high side + 160 mΩ low side, body diodes. xIN1/xIN2: 10 forward, 01 reverse, 11 brake, 00 coast. A sense resistor on xISEN limits the current to 200 mV / R (50 kHz chopping, slow decay); tie xISEN to GND without current control. nSLEEP high enables the chip (1 ms wake-up). Overcurrent above about 3.3 A switches the bridge off for 1.35 ms and pulls nFAULT low.

Datasheet ti.com ↗Open the editor
AIN1AIN2BIN1BIN2nSLEEPnFAULTVINTVCPAOUT1AOUT2AISENBOUT1BOUT2BISENVMGNDDRV8833PWPR
Schematic symbol

Key data

Category
ICs
Simulation model
Behavioural mixed-signal model
Manufacturer part number
DRV8833PWPR
Reference prefix
U
Pins
16
Land pattern
HTSSOP-16-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask2.46x2.31mm_ThermalVias

Simulation model

A behavioural model implements the interface of the chip (registers, protocol, timing) at its pins. The pins are connected to the analog circuit like CMOS pins.

Model
drv8833
Supply pins
12 / 13

Pins 16

PinNameUse
16AIN1Input pinBridge A input 1 (PWM possible)
15AIN2Input pinBridge A input 2 (PWM possible)
9BIN1Input pinBridge B input 1 (PWM possible)
10BIN2Input pinBridge B input 2 (PWM possible)
1nSLEEPInput pinSleep, active low: high = driver on (internal pull-down)
8nFAULTOutput pinFault output, open drain: pull-up resistor
14VINTPassive pinInternal regulator: 2.2 µF to GND
11VCPPassive pinCharge pump: 10 nF to VM
2AOUT1Output pinMotor A terminal
4AOUT2Output pinMotor A terminal
3AISENPassive pinCurrent sense bridge A: resistor to GND (I = 200 mV / R) or GND
7BOUT1Output pinMotor B terminal
5BOUT2Output pinMotor B terminal
6BISENPassive pinCurrent sense bridge B: resistor to GND (I = 200 mV / R) or GND
12VMSupply pinMotor supply 2.7–10.8 V: 10 µF to GND
13GNDGround pinGround and PowerPAD

PCB

Verified land patternHTSSOP-16-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask2.46x2.31mm_ThermalVias
PackageLand patternStatusSource
HTSSOP-16 · DRV8833PWPRHTSSOP-16-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask2.46x2.31mm_ThermalViasVerified land patternTI DRV8833 SLVSAR1E pin functions (PWP, HTSSOP-16, PowerPAD = GND); footprint = KiCad symbol Driver_Motor:DRV8833PWP
  • 11 10 nF to VM
  • 12 10 µF to GND
  • 14 2.2 µF to GND