Behavioural mixed-signal model10029449-111RLFhdmi_a
HDMI type A receptacle
HDMI type A receptacle, right angle, SMD with through-hole shell tabs (Amphenol 10029449). TMDS pairs D0±, D1±, D2±, CK± with their shields, DDC (SCL, SDA), CEC, +5V (to the sink, max. 55 mA), HPD from the sink. Plugged in: a monitor (1280 × 720) that answers with its EDID on the DDC lines, pulls HPD high when it sees +5V and shows the picture arriving on the TMDS lines in the display panel; or nothing.
Key data
- Category
- Connectors
- Simulation model
- Behavioural mixed-signal model
- Manufacturer part number
- 10029449-111RLF
- Reference prefix
- J
- Pins
- 20
- Land pattern
- HDMI_A_Amphenol_10029449-x01xLF_Horizontal
Simulation model
A behavioural model implements the interface of the chip (registers, protocol, timing) at its pins. The pins are connected to the analog circuit like CMOS pins.
- Model
- hdmi_a
- Supply pins
- +5V / GND
Pins 20
| Pin | Name | Use |
|---|---|---|
| D2+ | D2+Passive pin | Contact: carries a signal or supply wire |
| D2S | D2SPassive pin | Contact: carries a signal or supply wire |
| D2- | D2-Passive pin | Contact: carries a signal or supply wire |
| D1+ | D1+Passive pin | Contact: carries a signal or supply wire |
| D1S | D1SPassive pin | Contact: carries a signal or supply wire |
| D1- | D1-Passive pin | Contact: carries a signal or supply wire |
| D0+ | D0+Passive pin | Contact: carries a signal or supply wire |
| D0S | D0SPassive pin | Contact: carries a signal or supply wire |
| D0- | D0-Passive pin | Contact: carries a signal or supply wire |
| CK+ | CK+Passive pin | Contact: carries a signal or supply wire |
| CKS | CKSPassive pin | Contact: carries a signal or supply wire |
| CK- | CK-Passive pin | Contact: carries a signal or supply wire |
| CEC | CECPassive pin | Contact: carries a signal or supply wire |
| UTILITY | UTILITYPassive pin | Contact: carries a signal or supply wire |
| SCL | SCLPassive pin | I²C clock: sensors, displays; pull-up (about 4.7 kΩ) to the supply |
| SDA | SDAPassive pin | I²C data: pull-up (about 4.7 kΩ) to the supply |
| GND | GNDGround pin | Ground |
| +5V | +5VSupply pin | Supply input: decouple with 100 nF close to the pin |
| HPD | HPDPassive pin | Contact: carries a signal or supply wire |
| SH | SHGround pin | Ground |
Parameters 1
Plugged in
pluggedDefaultmonitor
monitornone
monitor: an HDMI monitor (1280 × 720 at 60 Hz) on a cable; none: nothing plugged in (no hot plug, no EDID)
PCB
Verified land pattern
HDMI_A_Amphenol_10029449-x01xLF_Horizontal| Package | Land pattern | Status | Source |
|---|---|---|---|
| right angle · 10029449-111RLF | HDMI_A_Amphenol_10029449-x01xLF_Horizontal | Verified land pattern | KiCad 10.0.7: symbol Connector:HDMI_A, footprint Connector_Video:HDMI_A_Amphenol_10029449-x01xLF_Horizontal |